Free patterns and tutorials:
- 2 fabric rectangles: 4 1/2 x 18 inches each for the roll basket
- 2 strips of fabric: 8 1/2 x 1 1/4 each to hang the basket
- Stranded cotton to match fabric colours
Marking the fabric before cutting
Get your outside fabric and draw the rectangle on it with a lead pencil.
Do not cut the fabric yet though you could cut the inside fabric as it won’t be embroidered.
Choose matching colours with high contrast.
Embroider some elements in a symmetrical manner or as you see it fit. Both ways work very well. You can see an example of random embroidery on a fabric print in my eye mask tutorial. This time I chose to embroider around the patterns in a systematic way.
I recommend you choose thread that has enough colour contrast or the embroidery will not show through like in this case. Both photos, above and below have some embroidery in light grey but it is hard to see because the colour is very similar to the fabric’s grey.
Once the embroidery is done, cut the rectangles along the marked lines.
You can cut the strips 2 strips of fabric, 8 1/2 x 1 1/4 each, which will be used to hang the basket. Fold the strips in half and then fold each side to the middle again and iron as per picture below.
Top stitch the strips very close to the edge.
Now pin the strips on the edge of one rectangle as per photo leaving 1/4 inch allowance on each side.
Place both rectangles together with the strips in the middle.
Sew around three sides of the rectangle, including the side where we pinned the strips.
Use the open side to turn piece inside out.
Iron well. Place the end of each strip and pin inside the open side of the rectangle. Fold each side in about 1/4 inch to make an internal seam.
Top stitch all around the rectangle.
Now pin the narrow sides together as per photo.
The sparte toilet roll is finished!
Detail of holder.
I have so far completed about 46 blocks of the Farmer’s wife quilt sampler. Homemaker is on the back burner currently until I can produce a reasonable block.
Hill & Valley
This bag was designed to accommodate quite a few items on the way back from the library.
- 12 charm squares or 5 inch squares (6 for each side of the bag)
- Scrap fabric for the top of the bag
- Scrap fabric for lace, sides and handle embellishments
- Scrap fabric for handles
- Lining fabric
- Medium weight one sided fusible interfacing
Body of bag
Place the charm squares on 2 rows per panel.
Sew both panels as per picture below. You will end up with 2 rectangles measuring 9 1/2 x 14 inches each.
Cut a rectangle for the top of the bag measuring 14 x 5 1/2 inches.
The side panels measure about 14 1/2 x 14 inches after stitching.
Cut a piece of fusible interfacing 14 1/2 x 14 inches and fuse to the wrong side of the panel.
Cut 2 pieces of fabric with the following measurements:
- Top: 6 inches
- Base: 2 inches
- Side: 14 1/2 inches
The resulting shape is an isosceles trapezoid with the top 2 inches wide and the bottom 6 inches wide.
Pin and stitch each piece to one of the panels as per picture below. Then iron flat.
Cut one 5 inch charm square in 4 strips like below.
Fold in half and iron, then fold each side in and iron again.
Top stitch each strip, make a tube with it and pin to the bag.
Centre the tabs as per picture.
Stitch to the bag at the top and bottom of the tab. Do 3 passes with the machine using a tight zigzag stitch.
Batting will only be added to the side panels.
Cut 2 14 x 14 1/2 inches rectangles and pin to the side panels.
Stitch along the seams of the charm squares to secure the batting.
Trim off excess batting when finished.
Stitch along the expandable sides seam as well.
Now place both sides of the bag right sides together and stitch along the sides.
Then fold the bag as per picture and stitch along the bottom.
When finished, fold the bag as per picture and stitch about one inch in the batting as per picture.
Cut the corner off.
For a better crisper finish, top stitch along the seams where the expandable side and the side panels meet.
This is what the expandable panel looks like after topstitching.
The finished size of each belt is 2 in x 29 in.
Cut 2 strips of fabric measuring 4 1/2 x 30 inches. Fold in half and stitch around leaving a 1/4 seam allowance. Leave a 2 to 3 inch opening on the side to turn belt inside out. Stitch the endings at an angle as per picture.
Turn belt inside out after stitching and close the opening. Iron flat.
Put the belt through the tabs as per picture.
Tie the sides.
Use each side of the bag to cut the lining. Place the sides on the lining fabric and cut.
Then sew both sides together leaving an opening at the bottom of the lining to turn bag inside out. For the lining leave 1/2 inch allowance instead so that the lining is slightly smaller than the bag.
To make the corners do as you did with the bag earlier. Stitch along the corner.
Place the lining over the outside bag as in the photo and pin.
Stitch along the top of the bag. The opening at the bottom of the lining is where we will be turning the bag around.
Turn bag inside out.
Top stick along the top of the bag.
Close the lining opening.
We are now ready to add the handles.
Cut 2 strips of fabric measuring 5 in x 22 1/2 in.
Cut 2 strips of interfacing measuring 4 1/2 in x 22 in.
Iron the interfacing to the wrong side of the fabric.
Fold strip in half as per picture and draw a half circle.
Stitch around the circle and the rest of the strip leaving a 1/4 inch seam allowance. Leave a 2 to 3 inch opening to turn handle inside out.
When turned, iron flat.
Top stitch for a crisper finish.
The handles are ready. They are quite wide because the bag is designed to carry a bit of weight.
Cut a rectangle 5 1/2 in x 1 3/4 in. Fold in half, then fold sides in and iron.
Using a needle, stitch at regular intervals making a frill as per picture.
Pull from both sides of the thread to obtain the desired length.
Pin to the end of each handle.
Baste in place.
Topstitch to secure frill to handle.
Then place the handle 2 inches in from the side of the bag.
Align the top of the bag with the end of the round part of the the handle as per picture below.
Sew handles in place.
The handle is sewn on the edge of the handles and then 1/4 inch in as well for strength.
The bag is finished.
Detail of bag
The bag is very roomy. The size can be adjusted by loosening or tightening the belts.
If you make this bag, please upload a photo to my Flickr group or Instagram and tag me with @teresadownunder.